DC-002D】DC电源插座/连接器 环保SGS
轻触开关,微型拨动开关,拨动开关,SS拨动开关,3.5耳机插座,2.5耳机插座,USB插座,DC电源插座,多功能五向开关专业生产各类DC插座,DC电源插座,USB插座等,外形美观,寿命长,用于家用电器,玩具,汽车音响,电脑及IT周边产品.DC插座DC直插式电源插座系列 DC贴片式插座
|
RATING（额定值）： DC 50V 0.3A | ||||
|
PRACTICAL TEMPERATURE RANGE 使用温度范围 |
-16~65ºC 在-16ºC~+65ºC温度内使用 | |||
|
STANDARD ATMOSPHEIC CONDITI** 测试标准状度
|
UNLESS OTHERWISE SPECIFIED THE STANDARD RANGE OF ATMOSPHERIC CONDITI** FOR MAKING MEASUREMENTS AND TESTS ARE AS FOLLOWS: (1) BETWEEN BODY AND CONDUCTOR: 5ºC TO 35℃ (2) BETWEEN CONDUCTORS NOT TO BE CONTACT：45% TO 85% (3) PRESSURE：86Kpa TO 106Kpa 在没有**的情况下测试温度、湿度、气压如下： (1) 温度为5℃~35℃ (2) 湿度为45%~85% (3) 气压为86 Kpa~106Kpa | |||
|
MECHANICAL（机械性能） | ||||
|
ITEM 项目 |
TEST CONDITI**测试条件 |
PERFORMANCE 规格 | ||
|
1
|
CONNECTION FORCE 插入力度 |
MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES。 依据标准的PLUG GAUGE 做第3次拔插后测定 |
3~20N | |
|
DISCONNECTION FORCE 拔出力度 |
MEASUREMENT SHALL BE MADE AFTER CONNECTING AND DISCONNECTING USING STANDARD PLUG GAUGE 3 TIMES。 依据标准的PLUG GAUGE 做第3次拔插后测定 |
3~20N | ||
|
2 |
TERMINAL STRENGTH 端子强度 |
A STATIC LOAD OF 0.1N/m(1kgf/cm)SHALL BE APPLIED TO THE TIP OF THE TERMINAL FOR 1 MIN IN ANY DIRECTION 向排脚先端的任意一个方向加1分钟0.1N/m(1kgf/cm)的力度. |
THERE SHALL BE NO DAMAGE TO THE TERMINAL SUCH AS CRACKS, LOOSENESS OR PLAY ELECTRICAL ,AND MECHANICAL CHARACTERISTICS SHALL BE SATISFIED 在排脚中没有裂开、松动等异常，满足于机械、电气性能 | |
|
ELECTRICAL（电气性能） | ||||
|
ITEM项目 |
TEST CONDITI** 测试条件 |
PERFORMANCE 规格 | ||
|
3.1 |
CONTACT RESISTANCE 接触电阻 |
MEASURED AT SMALL CURRENT （100m A OR LESS） 1000Hz 在微小电流（100 m A）以下测试 |
≤0.03Ω | |
|
3.2 |
INSULATION RESISTANCE 绝缘电阻 |
APPLY A VOLTAGE OF 500V DC FOR 1 MIN TO FOLLOWING PORTI** AFTER WHICH MEASUREMENT SHALL BE MADE: (1) BETWEEN BODY AND CONDUCTOR (2) BETWEEN CONDUCTORS NOT TO BE CONTACT (3) BETWEEN CONDUCTORS NOT TO BE WHEN PLUG IS INSERTED DC 500V 1 MIN 输入500V DC 电压1分钟，按以下接触方法测试： （1） 插座体与排脚之间 （2） 不接触的排脚之间 （3） 插头插入时不接触排脚之间 |
≥100MΩ | |
